Electric Mousetrap

I have seen many different mousetraps and rats throughout my life. Not that I'm fond of this somehow, but I just came across the mice from the house.
I'll tell you how to make a mousetrap that will kill the mouse by electrical discharge. The design is simple and uncomplicated as always.

What you need to make a mousetrap?

And also: wires, wires, a piece of profile, a bottle, hot glue, etc. We need a half liter plastic bottle. It is necessary to cut off the neck exactly. To do this, first mark up the cutting line with a marker.
Electric Mousetrap
We cut off.
Electric Mousetrap
We take a piece of galvanized profile for fixing drywall. Cut a small piece.
Electric Mousetrap
Take the switch.
Electric Mousetrap
Mark up the seat for it.
Electric Mousetrap
Drill a hole to the center,to make it convenient to cut.
Electric Mousetrap
Cut with scissors on metal or in another way.
Electric Mousetrap
Install the switch in the hole.
Electric Mousetrap
Unscrew the bottle cap halfway. We take a drill, fix a thin drill, and drill a hole in the cap without screwing it completely off the bottle. Drill on both sides. One hole is maximum at the top so that the passing drill does not touch the neck, and the second is as low as possible so that the drill goes through the lid and through the neck.
Electric Mousetrap
Next, fasten the cap and ream the hole on the neck of the bottle with a large hole.
Electric Mousetrap
Electric Mousetrap
Then, just below we make two more holes only on the necks with a thin drill.
Electric Mousetrap
Electric Mousetrap
We need a piece of wire.Bite off a piece of nippers.
Electric Mousetrap
We make a U-shaped and insert it into small holes. Electric Mousetrap Zagryat like this:
Electric Mousetrap
Screw the lid on before aligning the holes. Screw the screw into a small hole.
Electric Mousetrap
As a result, we have a knot, when rotating the lid on one side or the other side of the screw touches the wire. It will be a kind of switch.
Electric Mousetrap
Glue the resulting node to a piece of the profile.
Electric Mousetrap
Then take a piece of wire a little more, bend it like in the photo and push it into the hole on the other side of the lid. Fix with hot glue. This will be the electrode.
Electric Mousetrap
Putting together the entire structure.
Electric Mousetrap
Drill a hole under the wire.
Electric Mousetrap
Electric Mousetrap
Next, cut out a strip from the rest of the bottle and bend it. It will be a spring.
Electric Mousetrap
Electric Mousetrap
With hot glue we glue it exactly in the middle between the angle of rotation of the lid.
Electric Mousetrap
Electric Mousetrap That is, now, during any displacement of the electrode, it will return to its place.
Electric Mousetrap
Drill a hole for wires.
Electric Mousetrap
Solder wires, collect a chain. Electric MousetrapElectric Mousetrap
Electric Mousetrap
This is a high-voltage converter that converts 9 V from a battery to 7000 V.
Electric Mousetrap
Putting it on hot glue.
Electric Mousetrap
Skip the high-voltage wire and attach it to the electrode.
Electric Mousetrap
Electric Mousetrap
We isolate all joints with the same hot glue and attach to the body so that nothing dangles.
Electric Mousetrap
Electric Mousetrap
We also put the battery on hot glue.
Electric Mousetrap
Everything is ready.
Electric Mousetrap
Electric mousetrap

The principle of the mousetrap

A piece of fat is hung on a hook located in the center (mice and rats love it). The mouse approaches this piece and naturally tries to drag it away. She pulls him. As a result of this thrust, the contacts located on the roof close. And the high-voltage converter will run the current from the battery. The transducer electrodes are connected to the hook and bait and to the profile.As a result, a high voltage will be passed through a rat or a mouse that will try to drag off fat, which will kill the rodent.


Related News


Tourist Ax
How to make a kitchen apron
How to cook a juicy and tasty pork kebab in the oven
What is brillianite
How to cook a real jelly