How to make the ceiling lighting?

Watch the video

How to make the ceiling lighting?

Suspended ceiling with built-in lighting greatly transforms any room. And if the ceiling is slightly more difficult to LED lighting or duralight, then this interior will always please the eye and make a lot of impression on guests. So how to make the ceiling lighting in the room? Before you make a suspended ceiling with lighting, you need to determine the size of the protruding parts and the depth of the cornice. The average size varies, respectively, 38-43 cm and 13-22 cm. If there is furniture near the walls, then the width of the projections can be increased so that the spot lighting does not fall into the upper part of the cabinet or wall.

Preparatory work

The ceiling must be leveled with rough plaster. Places that will be covered with a ceiling, in order to save material, you can not align. First, by the given dimensions, we make the markings on the walls and on the ceiling. The average height of lowering the ceiling is 12 cm and it consists of a niche height - 9 cm and a cornice thickness - 11 cm.The exact dimensions will be different due to shpatlevaniya, but for convenience and installation, these figures are taken, because For the eaves, we can apply a 58 mm profile, which, in combination with both sheets of GCR, forms this size - 78 mm. When marking, perhaps, the horizon line to get to the wiring box and, if it interferes, it is necessary to deepen into the wall. It must be borne in mind that the standard strip of laying electrical wires along the wall runs 14 cm from the ceiling and can be damaged when the profile is fixed. So, if there is any doubt, it is better in some places to peel off the plaster and see how the wires pass.

For fastening are used mainly profiles 27? 28.5. Profiles 59.8? 26.9 are needed only for joining sheets of gypsum boards and the front of the eaves. Since the backs of the niches are carrying for all structures, they need to be made of GFL, which gives the necessary margin of safety. Fixed ceiling structure for further filling is fixed with spacers.

After puttying, priming and sanding from the pre-determined places for spotlights, the ends of the cables are removed.For RGB tapes, if they go 5 meters, a corrugated cable is carried out to the marked place, through which the LED tape is switched on in the circuit. When fixing the duralight, you need to determine the exit point where the terminal should pass freely. Next, make the installation of horizontal guides. It is more convenient to fasten the two extreme ones, to tension the cord to them and to make the entire assembly of the others using this cord.

Profile 59.8? 26.9 before installation must be prepared. At the junction of the C-shaped bend, it must be straightened or cut along the entire length of the profile, which will be more optimal. Then cut to size and secure the HL strips for the bottom of the niche. In this case, with additional sections of the profile, connect the profile of the bearing partitions and the profile of the eaves. This fastener produce only "seeds" - self-tapping screws 10-12 mm. This is necessary so that when re-screwing the screws do not come out of the gypsum board. Additionally, in the interval between the jumpers, make the fixing of the gypsum board in the opposite way, press down from above and set the screwdriver in ratchet mode. Next, mount the gypsum board (with pieces of maximum length) to the underside of the eaves of the suspended ceiling.Close the rest - the end of the eaves.

Further we fasten the guide corner to the corners of the eaves. When they are installed, they make measurements of the thickness of the shelf, the height of the niche and correct them, achieving the same parameters around the perimeter of the suspended ceiling. Putting out the bottom of a niche is carried out completely, constantly controlling the process visually. The bottom of the shelf should be flat - without cavities, bumps and voids. When filling the bottom of the false ceiling, at the junction of the gypsum plasterboard, a serpyanka or plaster net is used, but the joints can still crack. In order to make the LED ceiling lighting more qualitative, all the sheets are covered with wallpaper for painting.

Finishing work

After gluing the ceiling plinth, putty, primer and sanding in the ceiling, holes for the spotlights are cut out. If the marking and wiring is done accurately, they should be visible from these holes. Ceiling cover wallpaper for painting. Cut a hole under the lamp and start painting. It remains only to make the connection of the LED strip or duralight and laying the wires.

The corners of such a suspended ceiling can have any shape - it all depends on your chosen design. Convex, rectangular or rounded - design options are many. You can also say about the lines of the eaves, which can also have absolutely any and unique shape. In some nuances it will help you to qualitatively make the ceiling illumination of the video presented below.



Related News


How to get to Schelkovo
Psychologist vs girlfriend: who to go with the problem
Features cooking Idaho potatoes
Can I delete the temp folder
27 ideas of making lamps and chandeliers from bottles that will add uniqueness to the interior of your home
What foods help digestion
Stylish and fashionable skirts 2015 (17 photos)
Why do Russian women marry foreigners? Ask psychologists